AS

VF 测量支持六个或更多测量配置

错误行为：即使在 mapp Vision HMI 应用程序中将常数 NumResultsMax 配置为大于 5，也无法在 mapp Vision HMI 应用程序中捕获超过 5 个测量值。

纠错：可配置的测量次数是在构建过程中从视觉应用程序读取并传输到内部配置文件的。

无法解决此问题。

核心

节点号为 100 或更大的摄像头可在 mapp Vision HMI 应用程序中工作。

错误行为：对于节点号为 100 或更高的摄像机，无法在 mapp Vision HMI 应用程序中建立与摄像机的连接。

错误纠正：包含节点编号的 IP 地址存储在一个太短的字符串中。已调整字符串长度。

解决方法：使用小于 100 的节点号。

人机界面

如果结果列表太长，mapp Vision HMI 应用程序无法加载。

错误行为：如果初始设置结果列表的时间过长，则无法加载 mapp Vision HMI 应用程序。因此，当视觉功能常量 NumResultsMax 的值过高时，就会出现该错误。

错误纠正：使用 mapp 视图 "表格 "部件可加快创建结果列表的速度。

解决方法：打开 mapp Vision HMI 应用程序时，在 URL 中添加"?watchdog=0"。

操作系统

在摄像机启动后立即在不同的视觉应用程序之间切换可能会导致 ImageAcquisitionActive = TRUE 永久不变。

如果应用程序在摄像机初始化后直接更改了摄像机上的视觉应用程序，包括通过 mapp Vision 传输视觉应用程序，如果在应用程序应用视觉应用程序后立即采集图像，则可能导致 I/O 数据点 ImageAcquisitionActive 保持 TRUE。这样就无法再进行其他图像采集。

附注：如果 I/O 数据点 ResetAcquisition 被用于终止正在进行的图像采集或处理（ImageAcquisitionActive == TRUE），而不仅仅是重置待处理的图像采集触发器，则 I/O 数据点 ImageAcquisitionActive 也可能永久保持 TRUE。

AS

针对视觉应用程序名称长度的构建检查

已添加一项构建检查，用于检查视觉应用程序名称是否超过最大长度。

生成摄像机模块 I/O 映射时的扩展错误处理

修改了生成摄像机模块 I/O 映射时的错误处理。如果由于所使用的视觉应用程序配置错误而无法创建 I/O 映射，控制台将发出警告。

编辑器

德语编辑器现在也可用于德语 AS 中的 mapp Vision 配置文件。

人机界面

•可用性改进：

o视觉功能 "匹配 "的默认模型类型现在为 "形状模型"。

o加宽了滚动条，使其在人机界面应用程序的参数和变量列表中更加明显。

o每次采集图像以及在视觉功能之间切换时，人机界面应用程序中的图像处理结果列表都会被清除。

o更换人机界面应用程序中的组件时，重复模式会自动结束。

AS

VF Measurement supports six or more Measurement configurations

Error behavior: No more than 5 measurements could be captured in the mapp Vision HMI application even if constant NumResultsMax was configured to greater than 5 in the vision application.

Error correction: The number of configurable measurements is read from the vision application during the build and transferred to the internal configuration files.

A workaround is not possible.

Core

Cameras with node number 100 or greater work in the mapp Vision HMI application.

Error behavior: No connection to the camera could be established in the mapp Vision HMI application for cameras with node number 100 or higher.

Error correction: The IP address, which also contains the node number, was stored in a string that was too short. The length of the string has been adjusted.

Workaround: Use node numbers less than 100.

HMI

mapp Vision HMI application does not load if the result list is too long.

Error behavior: The mapp Vision HMI application cannot be loaded if initial setup of the result lists takes too long. The error therefore occurs with high values of vision function constant NumResultsMax.

Error correction: Creating the result list was accelerated by using the mapp View "Table" widget.

Workaround: Add "?watchdog=0" to the URL when opening the mapp Vision HMI application.

Operating system

Immediate switching between different vision applications after camera startup can result in permanent ImageAcquisitionActive = TRUE.

If a vision application is changed on the camera by the application directly after camera initialization, including transfer of the vision application by mapp Vision, this can result in I/O data point ImageAcquisitionActive remaining TRUE if an immediate image acquisition takes place after the vision application is applied by the application. Additional image acquisitions are then no longer possible.

Side note: If I/O data point ResetAcquisition is used to abort an image acquisition or processing in progress (ImageAcquisitionActive == TRUE) instead of just resetting a pending image acquisition trigger, I/O data point ImageAcquisitionActive I/O data point may also remain TRUE permanently.

AS

Build check for length of vision application name

A build check has been added that checks that the name of vision applications does not exceed the maximum length.

Extended error handling for generating I/O mapping of camera modules

Error handling when generating the I/O mapping of camera modules has been revised. A warning is issued in the console if the I/O mapping cannot be created due to configuration errors in the vision application used.

Editor

German editors are now also used for the mapp Vision configuration files in German Automation Studio.

HMI

•Usability improvements:

oThe default model type is now "Shape model" for vision function "Matching".

oThe scroll bars have been widened to make them more visible in the lists of parameters and variables in the HMI application.

oThe list of image processing results in the HMI application is cleared with each image acquisition and when switching between vision functions.

oRepetitive mode is ended automatically when changing the component in the HMI application.